Modular Control Devices – Pulsar S – ImpulseSwitches
Used to electromechanically or electronically control the switching of lighting and heating loads via a (brief) impulse to energise the control circuit in the home, commercial or industrial application.
- In accordance with BSEN60669-1, IEC 60669-1
- 16A or 25A nominal current
- 1P, 2P (1 module) and 4P (2 module) with various contact combinations
- 8V, 12V, 24V, 48V, 230V AC or DC Coils
- DIN rail mounting
- Circuit indicator window allowing clear labeling of circuits
- Central command modules (add-on or stand alone) for the control of several impulse switches
- Multilevel central command modules (add-on) for the control of several levels of impulse switches eg. Lighting in an office block
- 1n/o 1n/c left mounting auxiliary contact available
- IP20 terminals
- Contact flag indication
Modular Control Devices – Pulsar TS – StaircaseSwitches
Used for lighting or ventilation of staircases and halls etc. Push-button operated single-shot timer, switching the power to the load after the push-button has been pushed briefly, and switching off again after the presetted time has elapsed.
- In accordance with BSEN60669-1, VDE0632
- Delays from 0.5 to 12min
- 16A/250V nominal rating
- 1n/o contact
- 1 module width
- Operating voltage 230V
- IP20 protection
- Available in : Electromechanical, Electronic,Electronic Flasher, Din add-on module
- DIN rail mounted
Modular Control Devices – Pulsar T – TimeRelays
For lighting or ventilation applications where time delays are required either "ON" or "OFF".
- In accordance with BSEN60669-2-3
- Switching capacity 10A/250V
- 1c/o contact
- 1 module width
- Operating voltage 12-230V
- IP20 protection
- Available in: Delay On, Delay Off, Delay On/Off, Positive edge & Negative edge single shot, Symetrical flasher, Multifunctional
- DIN rail mounted
Modular Control Devices – Analogue TimeSwitches
Going from the pre-programmed switching of lighting (car parks, public roads) over pre-programmed switching of heating equipment to the pre-programmed switching of motors for pumps and fans and even to presence simulation.Easy to program by means of a dial on the front of the timer.
- In accordance with BSEN60669-2-3, VDE 0633
- 1, 2 channel versions
- Nominal current 16A/250V
- Operating voltage 220-240V
- With or without battery backup
- Available in day, week, day-day and day-week programmable versions
- Number of modules 1, 3 or 6
- Can be surface mounted or DIN rail mounted
Modular Control Devices – Galax – Digital timeswitches
Easy programming, used to control the switching of lighting (car parks, advertising signs, etc.) and heating equipment (home and office) as well as the switching of pumps and fans from the simplest to the most sophisticated application.
- In accordance with BSEN60669-2-3, VDE 0633
- High accuracy programming
- 1, 2 or 4 channel versions
- Nominal current 16A/250V
- Operating voltage 220-240V
- Clear LCD display
- Easy to program buttons
- All with battery backup
- Available in day, day-week and day-week-year programmable versions
- Number of modules 1, 2 or 6
- Antenna available for use with day-week-year timers to allow synchronization with Frankfurt atomic clock
- Hand held programming tool
- Can be surface mounted or DIN rail mounted
Modular Control Devices – 72×72 Classic andGalax Time Switches
Going from the pre-programmed switching of lighting (car parks, public roads, et.) over pre-programmed switching of heating equipment (homes and offices) to the pre-programmed switching of motors for pumps and fans.
Very easy programming by means of mechanical switches or digital buttons.
- day program, week program and day/week program
- 4 Modules
- Nominal current : 16/250V
- Operating voltage : 220-240VAC
Modular Control Devices – Galax – LightSensitive Switches
Easy to use timer to control lighting in shops, offices, car parks, advertising signs or even in the home via a photo cell to switch on/off a light when the light intensity drops below a programmed level.
- In accordance with BSEN60669-1, VDE0633
- Lux settings between 5-500
- 1 or 2 c/o contact options
- Nominal current 16A/250V
- 1 or 3 modules or wall mounting version
- Operating voltage 230V
- DIN rail mounting or wall mounting
- Surface mounting enclosure available for DIN rail mounted version
Modular Control Devices – Series T -Transformers
Used to supply power to bells and buzzers in the home or to supply power to control circuits for relays, contactors, impulse switches during the control of lighting and heating.
- In accordance with IEC 61558
- Bell transformer output power from 5VA to 30VA
- Safety transformer output power from 15VA to 60VA
- Bells and buzzers
- Two tappings on the secondary 8, 12 and 24V combinations
- 220-240V primary voltage
- Number of modules 1, 2, 4 or 6
- IP20 protection
- DIN rail mounting
Modular Control Devices – Series MT -Measurement Devices
Comprehensive range of analogue and digital measurement devices to measure voltage, current, frequency, hours, watts, kilowatt hours, power factor etc. in single phase and three phase circuits.
- In accordance with BSEN60051-1-2
- Analogue voltmeter, ammeter, frequency and hour counter meter
- Digital voltmeter, ammeter, frequency, wattmeter, kWh meter
- Digital multimeter / network analyser with optional remote communication
- Direct or indirect (CT) connection
- Appropriate CTs also available (not shown)
- Signal converters and selector switches
- DIN rail mounting
Modular Control Devices – Series PR – PriorityRelays
Priority relays offer the possibility to limit the energy consumption in installations with a defined maximum power. This limitation is getting measuring the installation total current continuously and in the case consumption would be higher then fixed value, priority relay would disconnect the non-priority load.
- In accordance with IEC 61095
- Nominal voltage : 230V
- Contact type : NO or NC
- 2 Modules
- IP20 terminals